How to put wire in a weed wacker

19.04.2021 By Talar

how to put wire in a weed wacker

How to Restring a Weed Eater and Respool the Spool

How to Put String On. Step 1 – Consult Your User Manual. Step 2 – Release the Spool. Step 3 – Cut the String. Step 4 – Begin Restringing. Step 5 – Wind the String. Step 6 – Clip In and Replace. How to String Echo. How to String Ryobi. FAQEstimated Reading Time: 4 mins. Follow these instructions for installing cutting line on a bump head string trimmer. To order trimmer line for your string trimmer, visit: vitoriayvitorianos.comt.

The plastic strings in weed eaters gradually wear down as a result of repeated contact with grass, weeds and hard objects, such as pavement, stones and trees. A few taps of the head on the ground is usually all that's required for the spool to unwind a few more inches of the string, but the reserve in the spool eventually dwindles and must be replaced. Some weed eater models simply require you to pop in a pre-strung spool, but most weed eaters require you to add new string to the spool.

Weed eaters might operate with one or two strings. Push in the tabs or turn to unscrew the retaining ring attached to the trimmer head to release the spool contained inside. The type of removal method varies with different weed eater models.

Remove the spool from the trimmer head. Cut a length of string how to test emergency lighting procedure 15 and 25 feet long, depending on the size of the spool.

If you cut the string longer than needed, you how to pass a lie dector test cut the extra string after winding the spool. Cut two identical lengths if your weed eater uses two strings. Locate the small hole or hole located at the center of the spool; string covers the hole waxker the spool is pug.

If your weed eater uses two strings, the spool should have two sections separated by a divider, with a hole in each section. Wind one piece of string at a time in two-string weed eaters. Wind the string onto the spool, following the direction what is the meaning of qualifications the arrow marked on the spool.

Wind the string onto the spool from side to side before overlapping to begin a second layer, so the string doesn't tangle when in use. Repeat with the second string on the opposite side of the spool, if applicable. Leave about 6 inches of string unwound at the end.

Clip the end of the string in the notch located on the edge of the spool. Weed eaters with two strings have two notches on opposite sides of the spool. The notches hold the string in place so it doesn't unwind while you replace the spool. Place the spool back in the hub inside the trimmer head. Release the loose length of string from the notches in the spool. Feed the loose ends through the eyelets -- usually called a line exit hole -- in the trimmer head. Repeat with the second string, if applicable.

Screw the retaining ring back onto the trimmer head or snap it eeed in place, if applicable. Wiggle the lut ring to ensure a secure fit, so it doesn't fly off when you power on the weed eater. Check your user manual or the writing on the trimmer head to find the specific size of string needed for your specific model.

The most common trimmer string size for gas-powered weed eaters are. The numbers refer to the string thickness. Some weed eaters might require you to remove the trimmer head from the body before you can release the spool. Remove the nuts that hold the trimmer head in place; replace the nuts after you reposition the trimmer head. A former cake decorator and competitive horticulturist, Amelia Allonsy is most at home in the kitchen or with her hands in the dirt. She received her Bachelor's degree from West Virginia University.

Her work has been published in the San Francisco Chronicle and on other websites. By Amelia Allonsy Updated December 17, Related Articles. Tip Ohw your user manual or the sacker on the trimmer head to find the specific size of string needed for your specific model. References Ryobi: Operator's Manual.

Step 1 – Consult Your User Manual

Stoney Ridge Farmer's "Quick Tips": HOW TO STRING YOUR WEED WHACKER. Hope you all enjoy this new series of quick how to videos here on the channel! Oregon. Master how to quickly change out a weed eater string (string trimmer line) on a typical trimmer. Check out the All About Outdoor Power playlist for more on g. Locate the starter holes in the spool. Insert the tip of the first length of trimmer line into one starter hole, and wind in the direction of the arrows. Wrap the line in neat, straight rows, to prevent jams later on. When there are about 5” or 6” of line remaining, snap it into the retainer on the spool to hold it in vitoriayvitorianos.comted Reading Time: 6 mins.

Last Updated: June 24, References. To create this article, 11 people, some anonymous, worked to edit and improve it over time. There are 29 references cited in this article, which can be found at the bottom of the page. This article has been viewed , times. Learn more Even the best lawn trimmers will eventually need new string. Doing this kind of maintenance can be intimidating for some people, but replacing the string on a trimmer is not difficult.

Before you change the string on a lawn trimmer, make sure your trimmer is turned off and that the engine is cool to the touch to avoid any injuries. Check on the manufacturer's website to see what kind of line you need and cut it to the correct length. Then, remove the retaining cap from the trimmer head and locate the start of the trimmer line spool. Start inserting your new line by wrapping it in neat, straight rows to avoid jams. Finally, line up the retainer with the slot on the outside of the head and reattach your retaining cap.

To learn how to change the line on a double-line trimmer, scroll down. Did this summary help you? Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. Edit this Article. We use cookies to make wikiHow great.

By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article methods. Tips and Warnings.

Related Articles. Article Summary. Method 1 of Prepare the line. The length and width of line you need varies based on your trimmer. If it has a gearbox, make sure it is cooled down. This will help prevent accidents. Remove the retaining cap from the trimmer head. This will probably involve either unscrewing it, pressing one or multiple tabs, or a combination of the two.

Locate the starter hole in the spool. Insert the tip of the trimmer line, and wind in the direction of the arrows. Line up the retainer with the slot on the outside of the head. Replace the spool into the trimmer head. Remove the line from the retainer, and pull it through the slot to make sure it is feeding smoothly. Method 2 of Locate the starter holes in the spool. Insert the tip of the first length of trimmer line into one starter hole, and wind in the direction of the arrows.

At this point, the line ends should be at opposite sides of the spool, to match the eyelets on the outside of the trimmer head. Remove the lines from the retainers. Thread them through the eyelets on the outside of the trimmer head.

Replace the spool into the trimmer head, and pull the lines through the slot to make sure they are feeding smoothly. Method 3 of Both lines should be cut to the same length.

Rotate the cap so the arrows align with the eyelets. You should be able to see light through the head when you look through the eyelets. Thread the end of the trimmer line through one eyelet. It should come through the eyelet on the other side of the trimmer head. Hold the ends together and pull to make both sides even.

There is an arrow on the spool to show you the direction in which to wind the line. Not Helpful 5 Helpful My weed eater has two slots on the head to thread pieces of string through. I can't get string to go inside one of the slots. What can I do? Check the size of the slots closely.

They're different sizes; select the one appropriate for your size of line. Not Helpful 1 Helpful 3. There are two methods used to mount the spool: 1. Tabs, as noted in this wiki, and 2. Screwed on, with threading going the opposite direction of operational spin. Not Helpful 0 Helpful 1. Trimmers generally do not require lubrication; in fact, lubricating the trimmer might attract dirt and increase the wear. Not Helpful 0 Helpful 0. How do I replace the string in a double wire weed eater that doesn't wind strings because they fold in half then go through two holes?

If you're referring to a string trimmer that doesn't have an line feed feature, you do exactly as you describe -- fold the lines in half, insert, and cut to length if needed. Double-line trimmers typically divide the spool into two halves one fore each protruding line.

If there is a hole between the two halves that is close to the center, you can cut a 25ft length of line, thread it through one of the holes so that one end is about 6in longer than the other, and then wind up both ends of the line simultaneously e. Include your email address to get a message when this question is answered.

By using this service, some information may be shared with YouTube. If you are having difficulty threading the cutting line into the starter hole in the spool, try cutting the tips at an angle. Helpful 4 Not Helpful 5. You will probably just break it. Take a step back, re-read the instructions, and review what you have done to try to troubleshoot what is not working. Helpful 3 Not Helpful 3. If you have a single- or double-line trimmer, disassembling the head is a good opportunity to clean it out.

Wipe it clean with a soft rag. Helpful 0 Not Helpful 0. This may also be a good time to apply lube to relevant parts. This will vary depending on your trimmer, but the spool or bearing may need to be lubricated. Submit a Tip All tip submissions are carefully reviewed before being published. Related wikiHows How to. How to. More References Co-authors: Updated: June 24, Categories: Landscaping Equipment.

Article Summary X Before you change the string on a lawn trimmer, make sure your trimmer is turned off and that the engine is cool to the touch to avoid any injuries.

Italiano: Cambiare il Filo di un Decespugliatore. Deutsch: Die Schnur an einem Rasentrimmer wechseln. Thanks to all authors for creating a page that has been read , times.

Did this article help you? Cookies make wikiHow better. By continuing to use our site, you agree to our cookie policy. About This Article.