What saw blade to use for laminate flooring

17.12.2020 By Voodoonris

what saw blade to use for laminate flooring

Using A Miter Saw: A miter saw is nice because all you need is a simple little mark and the saw will do the rest of the vitoriayvitorianos.com is the ideal tool and can cut perfect 90 degree cuts or any other angle, up to 50 degrees for most saws. You can use either a sliding model or a non sliding model, just make sure the blade is large enough to cut the entire width of the laminate flooring in one pass. Apr 09,  · Use a saw to cut the last plank to size. Hold on to the end of the plank you cut off, since you’ll use that to start the next row. Starting the rows with different-sized planks will create a staggered look, which actually makes the laminate flooring stronger.

When most people think about cutting laminate flooring I bet they think of using a miter saw and maybe a jigsaw for some of the specialty cuts but what they don't realize is that there are many different tools that will cut laminate flooring. Let's take a look at some of these pretty cool tools and I may even surprise you with a couple of them because you may have not known that they even existed.

Using some type of saw is the fastest and most common method to cutting laminate flooring but like anything else, it does have its drawbacks. For this example I am going to be using a miter saw which is the most common type of saw used and a circular saw which is less common but still very useful.

Using A Miter Saw: A miter saw is nice because all you need is a simple little mark and the saw will do the rest of the work. This is the ideal tool and can cut perfect 90 degree cuts or any other angle, up to 50 degrees for most saws. You can use either a sliding model or a non sliding model, just make sure the blade is large enough to cut the entire width of the laminate flooring in one pass. A Circular Saw: You can also use a circular saw but it will require additional tools like a square and some type of work surface to cut the laminate flooring on.

Sawhorses and a piece of plywood would make a pretty ideal workbench for this task and would be the easiest and most convenient method, in my opinion. If you do use a circular saw with a workbench like we looked at above, keep in mind that it will create a lot of dust on the floor and if this dust is on top of the newly installed laminate flooring, it is very slippery and you can easily fall. It would be a good idea to keep the vacuum or broom and dust pan on hand to clean up the dust periodically.

The jigsaw will be much slower than a circular saw or miter saw though so what saw blade to use for laminate flooring this in mind and it will usually burn through a good amount of blades. If you notice that jigsaw base is scratching the word you can always put a couple of pieces of tape on it to soften the metal base of the jigsaw and prevent any scraping or gouging that may occur while cutting.

A Table Saw: A tablesaw will come in very handy for making rip cuts on laminate flooring and is the fastest and most accurate way to do these types of cuts. No other tool will cut laminate flooring lengthwise better than a tablesaw.

These are more of a specialty tool and are only recommended if you have a lot of these types of cuts to make because they tablesaw is only useful for these types of cuts and nothing else so keep this in mind when looking at buying a tablesaw just for a one time laminate flooring install.

I wanted to touch on some specialty tools that can make the process of cutting laminate floors a lot easier and way more convenient than some of the other tools I just mentioned. These are smaller and more lightweight and some of them are even specifically designed for laminate flooring so they will make your job a lot easier, quicker and in some cases can create little to no dust in the process. The Dremel Trio: The Dremel Trio tool is a very cool addition to have when installing laminate flooring because it acts like a plunge router and can make what saw blade to use for laminate flooring work of circular, square or rectangle or cutouts in some of your floor pieces.

You will want to have plenty of bits on hand because the laminate flooring is a dense and hard material and will usually eat these bits up pretty quickly. The Dremel Saw Max: The Dremel Saw Max is basically just a mini circular saw that is a lot easier to use and has a much smaller blade so it can make tighter cuts.

These can be used for virtually any type of cut including crosscuts, rip what to expect from a 2 month old puppy and can even come in handy for cutting out floor vents. These are lightweight, easy-to-use and a lot safer than a large circular saw, which takes a lot of the awkwardness out of using the tool. I came across specialty flooring cutters that are specifically made for cutting laminate flooring and they work like a large paper cutter would.

One of the best things about these tools is the fact that they make no dust whatsoever. There are many different designs to these specialty cutters but they all function pretty much the same way and are used in the same way. You simply use leverage to cut the pieces, putting force down on the blade to cut the flooring. I have included a couple of pictures so you can get an idea of what they look like and how they work.

I have been in construction nearly my entire life and have a fascination with tools and love when they make my life easier. Match that with my "research addiction" and you create something like this website! Save my name, email, and website in this browser for the next time I comment.

Cool Tools. Facebook Twitter Pinterest Email. They each have their own advantages and disadvantages associated with them. Using A Saw To Cut Your Boards… Using some type of saw is the fastest and most common method to cutting laminate flooring but like anything else, it does have its drawbacks.

A Few Of The Disadvantages: A miter saw can be an expensive tool They tend to make a lot of dust They do not have the ability to rip a board lengthwise. Advantages: A circular saw can cut any direction, making perpendicular and parallel what is hi t drink Fast and efficient I would consider this method to use a minimal amount of tools. Disadvantages: Usually creates a ton of dust, like a miter saw would You will need to mark board first every time Circular saws can be very loud and awkward to use for some people.

Advantages: Jigsaws are relatively easy to use and one of the safest tools you can use They can cut any shape, which is something no what is a wise guy in the mafia tool can do Jigsaws usually tend to be less messy and are much quieter than any other type of tool. Disadvantages: They are one of the slowest cutting tools out there They can be very difficult to use when you want a perfectly straight line to be cut.

Advantages: Table saws can make the straightest cuts lengthwise Using these are the fastest way to rip a board lengthwise This is also the most accurate way to rip a board. Disadvantages: These can only be used for ripping and are not good for crosscuts These are extremely loud and make a ton of dust in the process If you don't already own one they will be labeled as an added expense for the project.

Specialty Saws And How to have a fun birthday I wanted to touch on some specialty tools that can make the process of cutting laminate floors a lot easier and way more convenient than some of the other tools I just mentioned.

Flooring Cutters: I came across specialty flooring cutters that are specifically made for cutting laminate flooring and they work like a large paper cutter would. Advantages: There is no dust made in the cutting process They are probably one of the safest and easiest tools to use for most people There is no skill required to use the tool like there would be for some of the other power tools I mentioned.

Disadvantages: These are only useful for crosscuts and will not work for ripping Some of these can be quite expensive and will only be useful for laminate flooring These can be hard to find at your local hardware store but are pretty readily available online.

About the author. Ryan I have been in construction nearly my entire life and have a fascination with tools and love when they make my life easier.

When cutting, the blade is not sharp enough to put a straight cut through the material, although this depends on how much of the laminate floors is floating past the blade. Most of the cuts cause some kind of chipping on the tongue and groove parts, which is not a . Mar 24,  · Set the depth of the saw a bit deeper than the depth of the flooring. Lift the blade guard and plunge the saw into the board, starting at 1 of the inner relief holes. Cut from hole to hole in a rectangular pattern to connect the inner section of relief holes you made and remove the center section.

This article was co-authored by Mark Spelman. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since This article has been viewed , times. Laminate flooring is a great alternative to wood.

Besides looking like wood, termites are not attracted by them, and they are easier to install. The easiest type of laminate floor boards are the type that lock in place. Next, cut strips of underlayment to size and lay the strips down across the exposed floor.

Underlayment will give you a flat, smooth surface to install the laminate flooring on. Use a saw to cut the last plank to size. Starting the rows with different-sized planks will create a staggered look, which actually makes the laminate flooring stronger. Place the first plank next to one of the walls in the corner, then snap the end of it into the next plank in the row using the built-in tongues and grooves.

Continue laying down planks in that row until you reach the other side of the room. Then, move onto the next row, starting with the end of the plank you cut off earlier.

Snap the tongues on the long sides of the planks in the second row into the grooves on the first row. When you reach the end of the second row, measure how much needs to be cut off of the last plank for it to fit. Cut the plank to size, then install it. Continue laying the rows like this.

Then, use a jamb saw to cut the trim so the plank is able to slip under it. Repeat on both sides of every doorway you encounter. When you get to the final row, measure and cut the remaining planks to the right width so they fit before installing them. Finally, remove the spacers and install quarter-round molding along the bottom edge of each wall to cover the gaps. To learn more from our Contractor co-author, like how to let your boards acclimate in your home, keep reading the article! Did this summary help you?

Yes No. Log in Social login does not work in incognito and private browsers. Please log in with your username or email to continue. No account yet? Create an account. We use cookies to make wikiHow great. By using our site, you agree to our cookie policy. Cookie Settings. Learn why people trust wikiHow. Download Article Explore this Article parts. Tips and Warnings. Things You'll Need. Related Articles. Article Summary.

Part 1 of Let the boards acclimate. Place unopened packages of laminate flooring in the room or rooms in which they are to be installed.

This should be done at least 48 hours before the laminate boards are placed so they have time to adjust to the temperature and humidity. This will minimize shrinkage or expansion when they react to room temperature and humidity. Check for moisture levels. Moisture can often destroy a perfect laminate floor installation, so before you begin, it is very important to ensure that your site is perfectly dry. Different meters will have different scales so you must always refer to the manual to ensure the correct reading.

Now check humidity levels within the room using a hygrometer. The sub-floor must also be perfectly level. An uneven sub-floor is another common cause of quality flooring installations failing. Use a spirit level and ruler to ensure that the floor does not have more than 3mm of dips or humps over a 1m length. Clean the floor. You will need to clean off the surface where you will be placing the laminate.

You can sweep the floor or use whatever method you prefer. Make sure the floor is completely dry as well. Lay a moisture barrier. Lay plastic lining on the floor of the room that will be covered with the laminate flooring.

Make sure to avoid overlapping as you do this because it may cause the floor to rise. If you have a concrete floor, run the plastic up the walls an inch or two not extending above the baseboard. Lay down your padding. This is to prevent any residue left on the floor such as small rocks and sand from causing dimples in the flooring and to give it a cushion.

It will also prevent any creaking or squeaking noises when people walk on the floor. Cut the foam lining to fit the floor and tape it down. Do not allow the foam to overlap. Part 2 of Place the first board. Place a board at the top left corner, finished side up, ridge side facing the wall. It is a good idea to lay the boards so that they are parallel to the longest wall in the room. Place spacers. Wedge a spacer between the end and edge of the board and the wall. You can buy spacers or make your own.

You will need several, six or more for the first two rows. Repeat for the second board. Place the next board the same way, laying it end to end, occupying the next spot along the wall. For the best results, make the entire first row parallel to the longest wall in the room. Make sure to check from the edges of the floor boards to the edge of the wall to make sure that the row is even with the walls. Move on to the second row.

Shorten the first piece of laminate flooring so the joints in this row will be offset staggered in relationship to the first row. Use a wooden block to tap the next row of boards into the first. Hold the block securely with your left hand and hit the block with a hammer in you right hand. The gap between the first and second boards should be closing. Keep hammering until the gap disappears.

Continue until each row is done. Make sure that the gaps between the boards are properly closed. Check the boards every third or fourth row to make sure that they are staying parallel to the wall. Trim planks which don't fit into the remaining spaces. When you reach the opposite wall or have to do odd shaped rooms, you will probably have to trim boards.

Measure how much you need and then cut the plank with a table saw. Use a sharp miter saw to cross cut the boards shorter and a table saw to make them narrower. It may be easier and provide better results if you cut the boards upside down. Don't forget your spacers! Don't forget to place spacers along all the edges of the room and remove them when the whole floor is done. Finish your floor.

You can finish your floor by placing baseboards, thresholds, or other finishing touches like staining. Scuffs or holes can be covered with special crayons available at your local hardware store. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube. Do not hammer on the laminate boards directly, they will break.

Use a scrap piece of flooring to hammer the board into place and it should just click in. Helpful 1 Not Helpful 0.